Skip Nav Destination
Search Results for 1.4 Drillstring Design
1-20 of 472 Search Results for
1.4 Drillstring Design
Journal: SPE Drilling & Completion
SPE Drill & Compl 24 (04): 508–517.
Paper Number: SPE-110708-PA
Published: 23 December 2009
...] was applied. The model indicated that drillstring failures would occur across shallow doglegs mainly because of high hang-down loads combined with slow ROP. The results of the study led to the development of new deep-well design criteria and implementation of new drilling guidelines. The new guidelines...
Paper presented at the SPE Annual Technical Conference and Exhibition, November 11–14, 2007
Paper Number: SPE-110708-MS
... of penetration, hook load, and drillstring configuration) was applied. The model indicated that drillstring failures would occur across shallow doglegs mainly because of high hang-down loads combined with slow rate of penetration (ROP). The results of the study led to the development of new deep-well design...
Journal: Journal of Petroleum Technology
J Pet Technol 41 (04): 401–404.
Paper Number: SPE-17183-PA
Published: 01 April 1989
... necessary for the second problem. Reciprocation was quickly ruled out because slack-off drag would severely restrict casing return to bottom, and the risk of lost returns caused by surge pressures would be high. Alternatively, rotation was chosen. This paper discusses the design and rotation of a 3,409-ft...
Paper presented at the International Petroleum Technology Conference, February 21–23, 2022
Paper Number: IPTC-21987-MS
.... In recognition of this, the dedicated operator and service team developed a drilling optimization roadmap that addresses the drilling challenges at the greatest performance impact. The optimization roadmap comprises enhanced trajectory design, drillstring design, drilling fluids and system hydraulics design...
Paper presented at the SPE/IADC Middle East Drilling Technology Conference and Exhibition, May 25–27, 2021
Paper Number: SPE-202174-MS
... drill pipe selection resonant rpm twist-off event software drillstring design frequency time curve drilling engineer drilling operation bha component upstream oil & gas drilling parameter vibration software critical resonant rpm force peak erratic torque hole section shear...
Paper presented at the SPE Annual Technical Conference and Exhibition, October 6–9, 1991
Paper Number: SPE-22548-MS
... a lightweight material. SPE SPE 22548 Design of a Lightweight Drillstring Using Composite Materials G.C. Eckold and E.A. Bond, AEA Technology, and G. Halsey, Rogaland Research Inst. Copyright 1991. Society of Petroleum Engineers Inc. This paper was prepared lor presentation at the 66th Annual Technical...
Paper presented at the University of Tulsa Centennial Petroleum Engineering Symposium, August 29–31, 1994
Paper Number: SPE-27976-MS
... safe, economical drillstring designs. This work assumes a well path has been specified and a drillstring has been chosen for evaluation. The procedures and options currently available for this evaluation are reviewed. The central role of torque-drag calculations in this evaluation is well recognized...
Paper presented at the SPE/IADC Middle East Drilling Technology Conference, November 8–10, 1999
Paper Number: SPE-57555-MS
... and bit. The use of vibration analysis software in the design of a BHA, to prevent buckling and to identify safe operating windows for rotary speed. The cost-effective deployment of vibration monitoring tools. The regular inspection of drillstring components. Field cases of the deployment...
S.. Flores, L.. Fagundes, Y.. Irokawa, A.. Schmidt, H.. Quinones, G.. Landinez, P.C.. C. De Oliveira, A.. Ramos, Y.. Medina
Paper presented at the IADC/SPE Drilling Conference and Exhibition, March 6–8, 2012
Paper Number: SPE-150664-MS
...-contractor team. A detailed engineering analysis of bit, BHA design and drilling mechanics was conducted to address the challenges of this section and propose a new approach to the drilling process. The key was the determination of the best combination of WOB and RPM to drill the different lithologies...
Paper presented at the SPE/IADC Drilling Conference, March 4–6, 1997
Paper Number: SPE-37597-MS
... the capabilities of such vessels when the water depths at the location exceed 500-600 meters. A solution to this is the usage of a light weight aluminum drillstring. The drill pipes described combines the large Russian experience in design, manufacturing and application of aluminum drill pipes for oil field...
Paper presented at the IADC/SPE Drilling Conference, February 18–21, 1992
Paper Number: SPE-23907-MS
... drilling applications. Use of the CDT system allows drillstring rotation, and does not require a split kelly. Finally, a back-up wet connect system for the CDT system has been designed and currently is undergoing field tests. When well conditions prohibit use of the cartridge system, the drillstring can...
Paper presented at the SPE Asia Pacific Oil and Gas Conference and Exhibition, September 20–22, 2011
Paper Number: SPE-147747-MS
... failures is the drilling conditions for any given run. drilling operation vibration severity index downhole vibration real time system upstream oil & gas correlation drillstring design quantification vibration intensity drill pipe selection severity index implementation vibration...
Publisher: Offshore Technology Conference
Paper presented at the Offshore Technology Conference, May 2–5, 1994
Paper Number: OTC-7566-MS
... wellbore radius. Through the use cI Gerber Fatigue Criteria, a Von Mises stress limit was established forthe complete downhole assembly (Figure 2). From this, guidelines were specified to minimize the possi- bility of stress cracks in the drillstring components. After in-house design review, the system...
Niko Spreckelmeyer, Thorsten Regener, Sascha Schwartze, Carl C. Clemmensen, Morten Eidem, Gaute Grindhaug
Paper presented at the SPE Bergen One Day Seminar, April 2, 2014
Paper Number: SPE-169208-MS
... directly above the liner running tool. The FLD is designed as a standalone tool that can be placed anywhere in the drillstring and can be used in different applications where enhanced hole cleaning is required, independently of the measurement-while-drilling (MWD) supplier. The tool ultimately must...
Paper presented at the IADC/SPE Drilling Conference, March 4–6, 2008
Paper Number: SPE-112529-MS
... increasing the chances of reaching fracture pressure compared with conventional drillstring operations. To negate the resultant increase in ECD, the rheological profile of the drilling fluid must be designed appropriately. This paper discusses a unique oil-based drilling fluid system weighted with treated...
Publisher: Offshore Technology Conference
Paper presented at the Offshore Technology Conference-Asia, March 25–28, 2014
Paper Number: OTC-25053-MS
..., the upper assembly consisting of the clutch, ESM and circulating v/v (connected to the drillstring) can be withdrawn from the stinger and lower BHA. The movement of the clutch segment retention collar is by a screw actuator driven by an electric motor. Electronics and Design Integrity The design intent...
Publisher: American Rock Mechanics Association
Paper presented at the 48th U.S. Rock Mechanics/Geomechanics Symposium, June 1–4, 2014
Paper Number: ARMA-2014-7108
... assembly bit design ongoing experimental study Drilling Assembly bit selection stick-slip vibration main driving mechanism experiment torsional vibration axial vibration compliance self-excited axial vibration drag bit axial compliance interaction experimental result Drilling vibration...
Amir Galaby, Miguel Cardenas, Ozgur Cengiz, Sameh Ibrahim, Ara Krikor, Slimane Sebanne, Artem Fedorov
Paper presented at the SPE/IATMI Asia Pacific Oil & Gas Conference and Exhibition, October 29–31, 2019
Paper Number: SPE-196533-MS
... high-interest parameters of every drillstring component in the wellbore. To fully exploit the modeling algorithms, it is required to input a comprehensive dataset including mechanical rock properties, cutting structure design, bit drive mechanism, drillstring physical characteristics, 3D well profile...
Paper presented at the IADC/SPE Drilling Conference, March 3–6, 1998
Paper Number: SPE-39391-MS
... inclination sin al drillstring design sail angle drilling operation friction rotation friction analysis eqn directional drilling mSociety of Petroleum Engineers iADC/SPE 39391 Friction Analysis for Long-Reach Wells B.S. Aadnoy, Stavanger U., and Ketil Andersen,* Statoil lIADCMember Copyright 1998...
Paper presented at the IADC/SPE Drilling Conference and Exhibition, February 2–4, 2010
Paper Number: SPE-128059-MS
... calculations. This paper also provides methods for evaluating these parameters with real-time data. torque spe iadc drilling conference rotation wellbore kinetic friction static friction upstream oil & gas drillstring design pipe drilling operation calculation diameter coefficient...
Product(s) added to cartClose Modal