An Analytical Model Coupled With Data Analytics to Estimate PDC Bit Wear
- Z. Liu (Halliburton) | C. Marland (Halliburton) | D. Li (Halliburton) | R. Samuel (Halliburton)
- Document ID
- Society of Petroleum Engineers
- SPE Latin America and Caribbean Petroleum Engineering Conference, 21-23 May, Maracaibo, Venezuela
- Publication Date
- Document Type
- Conference Paper
- 2014. Society of Petroleum Engineers
- 1.6 Drilling Operations, 1.6.3 Drilling Optimisation, 5.3.4 Integration of geomechanics in models, 1.2.3 Rock properties, 1.5 Drill Bits, 4.1.5 Processing Equipment, 5.6.1 Open hole/cased hole log analysis, 6.5.3 Waste Management, 3 Production and Well Operations, 4.1.2 Separation and Treating, 1.12.6 Drilling Data Management and Standards, 2.4.3 Sand/Solids Control, 6.1.5 Human Resources, Competence and Training
- Gamma Ray Log, PDC Bit Wear, ROP, Analytical Model
- 68 in the last 30 days
- 851 since 2007
- Show more detail
- View rights & permissions
|SPE Member Price:||USD 9.50|
|SPE Non-Member Price:||USD 28.00|
The increasing complexities of wellbore geometry imply an increasing potential of damage resulting from downhole bit wear. Although the locations of critical bit wear can be difficult to predict, the quantification of the actual bit teeth/cutter wear is important to achieve reduced cost per foot and predictable bit failure.
There is no acceptable universal mathematical model that describes bit wear accurately because of the complex nature of downhole conditions. Usually, either analytical models or real-time data analytics are used separately to estimate and predict bit wear. Combining both methods and using them simultaneously is an efficient way to address this limitation. This paper presents a new simple analytical bit wear model coupled with data analytics using real-time gamma ray data to suppress the uncertainties of the interacting formation properties and other intervening variables. The fractional bit wear of polycrystalline diamond compact (PDC) bit cutters is obtained from the geometric correlation between height loss and the cutter volume loss. The volume loss of cutters is assumed to be proportional to weight on bit (WOB), cutter sliding distance, rock strength, and rock quartz content.
The paper presents a field example to predict and estimate the bit wear using actual data. Gamma ray and rate of penetration (ROP) data of the initial drilling section are used to train the model to quantify the influence of formation strength interaction with the analytical model. Then estimation of ROP using the new bit wear model was carried out using actual field drilling parameters. The calculated ROP profile closely matched with the actual data within reasonable accuracy of less than 5%. Specific procedures are proposed for effective prediction of ROP and bit life.
|File Size||2 MB||Number of Pages||9|
Ebrahimi, M. and Noveiri, E. 2010. Cost Per Foot Reduction by Bit Run Optimization: A Simulation Study. Paper of SPE 133429 presented at the Trinidad and Tobago Energy Resources Conference, Port of Spain, Trinidad, 27–30 June. http://dx.doi.org/10.2118/133429-MS.
Gouda, G.M., Maestrami-Eni, M., Saif, M.A.A,. 2011. A Mathematical Model to Compute the PDC Cutter Wear Value To Terminate PDC Bit Run. Paper SPE 140151 presented at the SPE Middle East Oil and Gas Show and Conference, Manama, Bahrain, 25–28 September. http://dx.doi.org/10.2118/140151-MS.
Matahhari, H.R., Hareland, G., and James, J.A. 2010. Improved Drilling Efficiency Technique Using Integrated PDM and PDC Bit Parameters. Journal of Canadian Petroleum Technology. 49(10):45–52. SPE-141651-PA. http://dx.doi.org/10.2118/141651-PA.
Rahimzadeh, H., Mostofi, M., Hashemi, A.,. 2010. Comparison of the Penetration Rate Models Using Field Data for One of the Gas Fields in Persian Gulf Area. Paper SPE 131253 presented at the International Oil and Gas Conference and Exhibition, Beijing, China, 6–10 June. http://dx.doi.org/10.2118/131253-MS.
Rampersad, P.R., Hareland, G., and Boonyapaluk, P. 1994. Drilling Optimization Using Drilling Data and Available Technology. Paper SPE 27034 presented at the SPE Latin America/Caribbean Petroleum Engineering Conference, Buenos Aires, Argentina, 27–29 April. http://dx.doi.org/10.2118/27034-MS.
Rashidi, B., Hareland, G., and Wu, A. 2010. New Approach in Real-Time Bit Wear Prediction. Paper SPE 136008 presented at the Abu Dhabi Petroleum Exhibition and Conference, Abu Dhabi, UAE, 1–4 November. http://dx.doi.org/10.2118/136008-MS.