...) Q oprod = Oil Production Volume (STB) Q gprod = Gas Production Volume (STB) Q wprod = Water Production Volume (STB) Q winj = Water Injection Volume (STB) Q ginj = Gas Injection Volume (STB) B o = Oil Formation Volume Factor (Dimensionless) B g = Gas Formation Volume Factor...

... by inflow control devices (ICD). Primary depletion will be augmented by reservoir-specific water injection and hydrocarbon gas injection. Field characterization is being done based on data from comprehensive open- and cased-hole log suites, seismic data, MDT runs, PTA, and an array of SCAL and PVT tests...

... integration injection geological concept architecture interpretation sediment water injection Introduction Basic field data The Astokh field is the south part of the major offshore Piltun-Astokhskoye oil-gas-condensate field located in the north-east of Sakhalin Island, Russian Federation...

... Upstream Oil & Gas transmissibility barrier layer 12 society of petroleum engineers optimize field development plan reservoir simulation Field Development Plan pattern water injection History Match initial development plan development plan water injection Modeling & Simulation...

... of depositional environment and diagenesis, structural elements such as high permeability streaks and fractures, dynamic behaviors such as the water injection efficiency, gas cap expansion or coning. Secondly, numerical simulations were then run in order to rank the sectors based on the expected model...

... injection in the main structures. The short term was directed by executing workovers in areas where the water injection was in place. The asset value was recovered and increased as shown by a reserve’s replacement ratio of 1.13. This approach will serve as a framework for the future integrated development...

... geomechanics Waterflood Process fracture fractured reservoir equation enhanced recovery Upstream Oil & Gas displacement discontinuity method fracture propagation tight reservoir permeability water injection fracture model society of petroleum engineers Introduction Waterflooding...

... Gulf clysmic fault communication society of petroleum engineers saturation water injection Reservoir Characterization structural uncertainty appraisal block ra el ush field Upside Potential Upstream Oil & Gas reservoir pressure aquifer injection Ra El Ush Introduction...

... Precipitation asphaltene deposition injection natural depletion reservoir performance History aquifer reservoir Upstream Oil & Gas deposition oil column gas injection Scenario remediation of hydrates oil production recovery factor water injection water flooding Introduction...

... Abstract Waterflooding has been an effective method for improving oil recovery process of Low-Permeability Reservoirs. Tight Low-Permeability reservoirs are characterized by natural fractures, hydraulic fractures, and induced fractures by water injection. These fractures may have a significant...

..., field injectivity tests, pilot water injection and intensive surveillance plan. Water injection is part of field redevelopment plan and will increase recovery factor by 7.3%. Upstream Oil & Gas mobility ratio sweep efficiency fracture pressure injector viscosity producer interpretation...

...Reservoir Simulation Study 2006 A full field compositional study was completed for Lower reservoirs X and Y in 1992. Based on this study, five producers and seven water injectors were drilled to sustain 10 Mbd plateau production rate with peripheral water injection. The strategy to maintain...

... was natural depletion above bubble point. At that time water injection was started and has since been extended to all the field. Based on pressure performance data, the reservoir could be divided into five relatively independent producing areas. In initial field development, material balance techniques were...

... upstream oil & gas wag ratio producer gas injection injector sector modeling study gas injection method spe 147999 pressure support modeling & simulation breakthrough reservoir pressure line drive reservoir gravity override gas injection pilot water injection injection production...

... these modeling techniques can be used to design a CO 2 storage process in saline aquifers. The following results are obtained: Solubility trapping and residual gas trapping are competing mechanisms. Residual gas trapping is important in low-permeability aquifers and water injection can be used to accelerate...

... and vertical fluid flow behavior, an inverted 5-spot water injection pilot pattern is being implemented. The pilot will address the issues of the uneven sweep efficiency, bypassed oil and effectiveness of stylolites across different units. The pilot results and observed data will be used in the simulation...

... of any oilfields in the world. Waterfloods in fields that have operated for many years are reaching a stage in which better understanding of the reservoir’s response to water injection is critical for optimal field management going forward. A common approach, however, is that existing data sets are often...

... waterflooding reservoir pressure producer Reservoir Energy information fusion Mauddud reservoir Kuwait pattern balancing Artificial Intelligence Upstream Oil & Gas water injection spe 111406 reservoir drillstem testing ma-sp super giant carbonate mauddud reservoir drillstem/well testing...

... with production history of DST results. Eventually the model was applied to run a series of sensitivity simulations for optimization of injector locations, Water injection and gas injection (miscible and immiscible) to increase reservoir oil recovery. Based on simulation results for different scenarios water...