1-11 of 11
Keywords: assembly
Close
Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Proceedings Papers

Paper presented at the Offshore South East Asia Show, February 2–5, 1988
Paper Number: SPE-17658-MS
... of the BIMA development drilling program, Atlantic Richfield Indonesia, Inc., had succeeded in drilling over 18,200' of horizontal hole in eleven wells and 4200' of hole at angles from 85 to 90 in five wells. P. 68^ atlantic richfield indonesia wellbore path development well assembly reservoir...
Proceedings Papers

Paper presented at the Offshore South East Asia Show, February 2–5, 1988
Paper Number: SPE-17665-MS
... and emulsion breakdown. Extensive investigation eventually led to the specification of an unweighted refined oil as a suitable replacement packer fluid. The workover program further showed that the seal assembly in every polished bore receptacle (PBR)/seal assembly type of completion was firmly stuck...
Proceedings Papers

Paper presented at the Offshore South East Asia Show, February 2–5, 1988
Paper Number: SPE-17668-MS
... packer. With the P.Xpressed desire to underbalance perfor3tP., ~he requirement for positive gas pressure contninment, and the need for secure ·casing a~chorage, a special packer and associated gravel pack assembly was essential. Page 2 Canpletion Systans for Large Diameter Casing OSEA/88168 RESULTS...
Proceedings Papers

Paper presented at the Offshore South East Asia Show, January 28–31, 1986
Paper Number: SPE-14615-MS
... used to obtain the earliest possible kickoff points. Both jetting and mud motor/steering tool assemblies were used to build angle at rates of 3-5/30 m, depending on proximity of adjacent wells, formation drillability, and the respective target locations. Surveys were taken by conventional single shot...
Proceedings Papers

Paper presented at the Southeast Asia Show, February 21–24, 1984
Paper Number: SPE-12425-MS
... management & disposal downhole intervention texas bottom hole bottom hole pressure application circulation drilling operation back pressure stable foam assembly well intervention foam solution liner 5th Of+shore South East Asia 21-24 February 1984 Singapore SESSIGN 10: WELL COMPLETIONS...
Proceedings Papers

Paper presented at the Southeast Asia Show, February 21–24, 1984
Paper Number: SPE-12422-MS
... seal assembly completion installation and operations drilling equipment marine wellhead operator casing and cementing valve guidance alternatively template completion equipment upstream oil & gas spool wing valve application assembly conductor wellhead riser hanger means...
Proceedings Papers

Paper presented at the Southeast Asia Show, February 21–24, 1984
Paper Number: SPE-12423-MS
... developed to comply with the more stringent improved fire-resistance specifications. CIDE DCCICT~NT CnN<ll)FRAT1nNS1 L1\ L4S*. . . . . . . . . .. A typical nan-firesafe wellhead assembly is illustrated in Figure 1. This conventional design has several weaknesses which are responsible for its low level...
Proceedings Papers

Paper presented at the Offshore South East Asia Show, February 9–12, 1982
Paper Number: SPE-10438-MS
... alluvium. This paper describes how drilling time and problems associated with rough drilling were reduced by using a downhole mud motor to power a stabilized 26 in. drilling assembly. Introduction The Tiwi Geothermal Field is located on the flanks of the extinct Malinao Volcano approximately two hundred...
Proceedings Papers

Paper presented at the Offshore South East Asia Show, February 9–12, 1982
Paper Number: SPE-10454-MS
... strategic planning and management inspection assembly subsea system project management objective tlp operation hull tunnel interpretation hutton tlp engineering configuration contribution tension leg hutton tlp design upstream oil &amp; gas hutton field evolution contractor...
Proceedings Papers

Paper presented at the Offshore South East Asia Conference, February 21–23, 1978
Paper Number: SPE-7100-MS
...-on assemblies were expensive. They required pipe upsets which were long and heavy. The pipe ends and the mating portions of the tools joint required close tolerance machining and the loss of length, when the pipe ends were screwed into the tool joint members, was considerable These shortcomings pointed the way...
Proceedings Papers

Paper presented at the Offshore South East Asia Conference, February 17–20, 1976
Paper Number: SPE-5972-MS
... recess in the casing seal assembly and lock the hanger securely into place. The running toot is released from the hanger by dropping an unlock dart down the drill pipe and applying fluid pressure down the drill pipe onto the top of the dart. This pressure moves a sleeve from behind the dogs...

Product(s) added to cart

Close Modal