... thebes formation fracture gradient young strength magnitude Introduction The Gulf of Suez Basin is the most important oil province in Egypt. Many discoveries have confirmed its economic potential. Bakr oil field is located on the western side of the Gulf of Suez. Bakr field is situated 170 km...

... Pérez-Robles et al. (2019) prepared a gel system based on HPAM with formaldehyde and resorcinol as crosslinker. In this study, the tested silicon dioxide (SiO 2 ), aluminium oxide (Al 2 O 3 ), Magnesium Oxide (MgO), and chromium oxide (Cr 2 O 3 ) nanoparticles as additives. The gel strength...

.... Buoyancy installed on the SLWR helps reduce top tension and decouple vessel motions from the riser touchdown zone, which ensures that the required strength and fatigue performance can be achieved. SLWR and SCR configurations are developed for mild environment, deepwater applications representive...

... Upstream Oil & Gas cylinder application installation force society of petroleum engineers Makeup Torque cam device special tool installation Drilling Equipment connector teeth key quantity performance difference installation time strength torque CAM anti-rotation device...

... more than 200 ICD installations in several fields ( Al-Khelaiwi, 2013 ). The ‘strength’, or extra pressure drop, added by an ICD restriction is calculated from the flow rate ( Q 2 ) and a calibration factor ( a ): (1) Δ P ICD = a   Q 2 This pressure drop may be generated...

... FAT hydrostatic pressure test The equivalent primary membrane stress shall be equal or less than 90% of the yield strength. The equivalent value of the summation of the primary membrane and bending stresses shall be equal or less than 135% of the yield strength. The equivalent value...

... Corrosion flowline corrosion operational safety strength assessment protection inspection redundancy requirement well integrity KPIs hazard mobile installation subsea system structural integrity Indicator mooring system Upstream Oil & Gas Offshore Installation performance indicator...

... Pipeline Corrosion well integrity separator assembly materials and corrosion Upstream Oil & Gas fabrication bonding material loading bonding agent society of petroleum engineers application substrate finite element analysis Subsurface Corrosion strength reinforcement plate hot work...

... for a while, but pressure will usually rebuild. How fast the pressure rebuilds depends on the pressure difference and the size of the leak path. Causes of Sustained Casing Pressure cement formulation Upstream Oil & Gas cement chemistry cement property casing and cementing strength ambient...

... not take into account the size of the fire threat against which the PFP is designed and could lead to less than conservative results as it only considers removing one member of the structure at a time, without considering reduction in the strength of the surrounding members as they are also being heated...

...-fire integrity of phenolic and polyester FRP gratings to determine whether such gratings can be safely used following exposure to fire. Firstly the range of weights of offshore workers was established. The recommended residual strength required for post-fire use should exceed the load generated...

... Does orientated perforating reduce sand production (taking into consideration differences in perforated intervals, porosity, rock strength and production rate)? Does orientated perforating make the erosional velocity profile within the production liner worse than with a 60° spiral...

... barriers of a particular strength which are a combination of density and thickness of the barrier. The facility process inventory, equipment, organization and people will change over time; the thickness of the barrier will fluctuate. The vulnerability of a facility depends on the gap between...

... and materials casing and cementing HPHT Drilling Equipment drilling fluid management & disposal complex reservoir Upstream Oil & Gas specific energy high pressure high temperature diameter completion strength application assembly casing design drilling operation resin spallation...

.... The strength of the consolidated material depends on the particle size of the treated sand. Using uniaxial compressive strength (UCS) test equipment, the compressive strength was measured up to 1500 psi with fine sands, and 450 psi with coarse sands or proppants. The shelf life time of the system was found...

... on the header and/or branch. Loads on the grout SSGT is a structural component and the grout has to transfer the loads between the pipe and the branch and vice versa. The properties of the grout, such as compressive, flexural, cohesive and adhesive shear strength were selected to meet the specified...

... mudstones showing strength anisotropy. Minimum required mud weight predictions were made for a range of well configurations. The results of this study were used to plan an Extended Reach Drilling (ERD) development well targeting a previously undeveloped part of the Clair field. The new well was successfully...

... of the pipe are described. A brief overview of qualification tests is provided along with a description of initial applications. This technology has the potential to be a ‘game changer’, enabling new, lower cost field development solutions in offshore areas around the world. subsea system strength...

... Abstract The methodology for predicting sand production is in general constant across the industry. That is the determination of formation strength and field stresses and the application of them to a failure model. However, the variety of models available and their applicability and accuracy...

... ppg Reservoir Characterization strength subsurface uncertainty in-situ stress MEM well logging elastic moduli formation strength exploration lithology reconciling subsurface uncertainty travel time salt clastic boundary appropriate well design wellbore design spe 108848 moduli...