... to test only polymer flooding because of cost considerations. This study is to design fit for purpose long-term polymer injectivity (LTPI) pilot using produced water (salinity 230000ppm) with the objectives of testing injectivity, adsorption, breakthrough, resistance factor and response time within 6-12...

... in three target layers and seven producers, completed in similar or other different layers. Unique gas tracers were injected into isolated layers independently at different times to evaluate the injector-producer connectivity in each layer. The producers and re-injected gas were sampled for one year...

.... Activities undertaken to forecast the gas injection pilot performance include a two-pronged strategy of using calibrated hybrid sector model realizations and simple box models. The box-models captured range of gas injection phase outcomes on a simplified finer resolution of injector-producer models, testing...

... was developed to flow the well to the facility through a temporary installed 6.5km HT Reinforced Thermoplastic Pipe (RTP) in an uneven landscape to connect the well to the nearest existing producer carbon steel flowline. The developed procedure enabled the successful achievement of maintaining zero routine...

... that could overcome the barriers to meet this transition. However, there are many challenges associated with hydrogen energy since it requires vast storage volumes. Several new technologies have been proposed to store and produce hydrogen efficiently. One of the most promising storage technologies...

...Discussion and Conclusions We have successfully tested the idea of scale inhibitor (SI) injection with the MEA-based alkali-surfactant (AS) formulation as an alternative to make-up water softening and scale squeezing of the producer wells. The main results of the Scaling Inhibitor field trial...

... reservoir pressure management subsurface storage enhanced recovery climate change injector reservoir simulation reservoir surveillance production control relief well boundary efficiency placement depth storable quantity producer geology pressure management scheme injection lcc chemical...

... the timeline for fracture propagation to reach the producer wells. Geomechanical modeling results were integrated with well and reservoir management (WRM) activities and surveillance technologies to optimize the injection strategy for improved waterflood performance. Formation fracture pressure data were used...

... producer waterflooding facility design development concept oil producer water injector society of petroleum engineers ksi field fast track completion design Surface FacIlity producer Waterflood Development analogue field Introduction KSI is a green field located ~16 km northeast of W...

... Abstract Understanding the full-cycle cost of oil and gas exploration, development, and production is critical for petroleum producers and all players in the oil and gas industry. In particular, full-cycle cost assessment is used for corporate planning, acquisitions, operational improvements...

... Abstract Russia always plays an important role on iternational energy markets as one of the major oil and gas producers and exporters since the country entered international enrgy market in the middle of the last century. And this role will remain stable at least till the year 2040 according...

... in the pre-Permian section. The Lower Cretaceous Kharaib Limestone is an oil reservoir. The unit was tested in different exploratory wells in the early life of the Bahrain Field and it was found to be of low permeability but produced oil. The first phase of field development in Kharaib was initiated...

... to prove the concept of polymer sweep, a field trial was designed and conducted successfully in the field. Moreover, due to the challenges associated to handling back produced polymer number of tests were conducted to assess the impact of polymer on facilitates. Development of the field will take place...

..., premature water breakthrough was observed in most of the producers. Rapid water breakthrough in Mauddud A (Ba) is attributed to presence of high permeability vugs and layers resulting in water cycling and poor sweep in the matrix leaving bypassed oil. Following recommendations from the 2013 partner Peer...

... to propose the best way to improve it. The workflow starts with first building a material balance model to understand the main reservoir driving mechanisms. Second, a fine-scale history matched simulation model was used to understand the main reasons of the current low recovery. A Produce High and Inject...

... of integrated study in which ‘multi-stage hydraulic fracturing’ was recommended as the most optimum stimulation technique in order to enhance the productivity of all the proposed horizontal producers. Importance of DPDP model increases multi-fold when contrast between fracture and matrix permeability...

... in the study aids in investigating many optimization scenario within a short period of time. chemical flooding methods Upstream Oil & Gas enhanced recovery injector Artificial Intelligence polymer injection optimization problem viscosity row producer reservoir modeling & simulation...

... for 2.5 years: It has one horizontal well in the gas cap, one vertical producer, four vertical injectors with three Temperature Observation Wells (TOWs) clustered around one of the injectors. First pilot performance was assessed and confirmed in reducing the residual oil in the gas cap by distillation...

... implemented to propagate the petrophysical properties within a sequence stratigraphic framework. The 3D static model was built based on real field data, using several wells. However, for the purpose of the simulation work done in this study, only a crestal oil producer and a downflank water injector in a line...

... provides the causal relations between the major components of the market including the determinants of the supply and demand. We divide the supply into the OPEC, non-OPEC and US producers. Further, we have extracted the supply of Iran, Saudi Arabia, Libya, Venezuela, and Iraq in the OPEC, and Russia...