1-11 of 11
Keywords: separator
Close
Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Proceedings Papers

Paper presented at the SPE Gas Technology Symposium, April 28–May 1, 1996
Paper Number: SPE-35610-MS
... was approximately 3% lower than the drier gas measured by the new meter. Possible reasons for this metering deviation are discussed in the paper. deviation separator swirl angle gas stream configuration flow metering pitot probe indian basin field separation and treating velocity profile accuracy...
Proceedings Papers

Paper presented at the SPE Gas Technology Symposium, January 22–24, 1991
Paper Number: SPE-21486-MS
... the hydrostatic pressure of a column of brine to the surface. Production could be started by flowing directly to tanks until gas production lightened the column to the point where wellhead pressure was high enough to drive the separator. Furthermore, after drawdown to below hydrostatic pressure, a few swab...
Proceedings Papers

Paper presented at the SPE Gas Technology Symposium, January 22–24, 1991
Paper Number: SPE-21485-MS
.... Calcium carbonate scale formation in the well tubing and separator equipment was controlled by the injection of a scale inhibitor into the flow line and by twice successfully injecting inhibitor "pills" directly into the reservoir. Corrosion and/or erosion of piping and equipment was also significant...
Proceedings Papers

Paper presented at the SPE Gas Technology Symposium, January 22–24, 1991
Paper Number: SPE-21506-MS
... ABSTRACT Prediction of performance of Separators and Gas Scrubbers is difficult with the traditional design methods - especially if inlet liquid loadings are high. BP Engineering has developed a novel Separator Design Program that can quantify the performance of both conventional...
Proceedings Papers

Paper presented at the SPE Gas Technology Symposium, June 7–9, 1989
Paper Number: SPE-19077-MS
... Abstract Venturi meters, used in combination with relationships published for orifice plates to correct for wetness, can accurately meter wet gas. This allows separators to be omitted from gas field developments where they were used only to remove entrained liquid before the gas was metered...
Proceedings Papers

Paper presented at the SPE Gas Technology Symposium, June 7–9, 1989
Paper Number: SPE-19080-MS
...-proven process to improve economics in some areas of gas production. Engineers familiar with modern gas plant operation, particularly cryogenic plants, are acutely aware of the need for gas dehydration. This concern for hydrate prevention carries over into low temperature separation in the field...
Proceedings Papers

Paper presented at the SPE Unconventional Gas Technology Symposium, May 18–21, 1986
Paper Number: SPE-15255-MS
... inhibition production monitoring wellhead production history drawdown reservoir barrel hydrate remediation production chemistry separator remediation of hydrates surface facility pret well acid valve recovery reservoir pressure brine separation and treating reservoir surveillance primary...
Proceedings Papers

Paper presented at the SPE Unconventional Gas Recovery Symposium, May 16–18, 1982
Paper Number: SPE-10835-MS
... the wellhead tubing and annulus, separator, and disposal wellhead pressures. Differential pressure transmitters (DPTs) provided continuous readings across the flare line orifice plate and downstream brine filters. Temperature transmitters relayed wellhead brine, flare line gas, and disposal brine temperatures...
Proceedings Papers

Paper presented at the Gas Technology Symposium, September 15–16, 1966
Paper Number: SPE-1635-MS
... if not all cases gas is delivered to the aquifer by way of compression from a pipeline, and as such has been dehydrated and sweetened. dehydration faci lity flow rate operation aquifer lateral heater hydrate glycol Upstream Oil & Gas separator storage field gathering system...
Proceedings Papers

Paper presented at the Gas Technology Symposium, November 18–19, 1965
Paper Number: SPE-1352-MS
... spending nearly a month fishing, the well had to be abandoned due to mechanical difficulties in the hole. The rig was skidded 100 feet north and the Edenborn #2-A was completed May 25, 1964, flowing P. 1^ Upstream Oil & Gas Drillstem Testing separator oil company porosity oil zone...

Product(s) added to cart

Close Modal