..., tests are often conducted using available outcrop core and scaled down reservoir conditions. Laboratory tests reduce higher field pressures down to lab scale. In certain scenarios, simulating the total gas flux in a given near-wellbore system is achieved by increasing gas flow rates. Although, in some...

... method, optimizing the sand control selection to the well. sand/solids control wellbore design completion sand control upstream oil & gas lafayette wellbore integrity louisiana test media screen selection flow rate sand control system premium mesh screen cyclical brine test method...

... to have minimal effects. well control managed pressure drilling circulation flow rate rotational speed annular pressure drilling dp rotational speed mud density drilling fluids and materials cfd model flow rate diameter ecd analytical relationship pressure loss geometry rheological...

... used to visualize the wormholes formed. Rates of penetration were gained from differential pressure data combined with consideration of peak elution time of Ca 2+ from the analysis of effluent samples. In tests performed on comparable outcrop limestone core samples, with the same injection flow rate...

... in comparison to plain HCl acid, whereas the most notable volume reduction occurred when nonoptimal flow regimes were used. At flow rates of 1 mL/min, the formulated HCl acid fluid provides more than a five-fold PV bt reduction under similar conditions. More importantly, core face dissolution, characterized...

... ). Introduction Production Chemistry Upstream Oil & Gas enhanced recovery conformance improvement chemical treatment higher temperature fluid compatibility emulsion droplet flow rate polymer gel system oilfield chemistry rock/fluid interaction Conformance Control stability emulsified gel...

... reservoir society of petroleum engineers drilling fluid property specification circulation flow rate fluid loss requirement hole cleaning RDIF rheology reservoir characterization well control enhanced recovery wellbore integrity drilling fluid management & disposal complex reservoir...

... and materials drilling data acquisition measurement while drilling well control annular pressure drilling flow rate onshore testing operator Upstream Oil & Gas pulser BHA loss scenario MWD tool production monitoring manage ultra-high lcm concentration cement squeeze operation lcm society...

... adsorption reduction flow in porous media sand production gas well Permeability reduction enhanced recovery Polymer Treatment injection permeability water production Zaitoun polymer injection flow rate relative permeability gas relative permeability reservoir intervención de pozos petroleros...

... and formulation drilling fluids and materials enhanced recovery drilling fluid property fracturing materials hydraulic fracturing fracturing fluid Upstream Oil & Gas polymer concentration flow rate polyacrylamide polymer drilling fluid formulation shear viscosity viscosity chemical flooding...

... permeability DDS is significantly more effective than the traditional DDS. In all cases, the use of the low permeability DDS predicts a larger pressure response resulting from the temporary blocking of high permeability zones as well as better acid injectivity in low permeability zones. Based on the flow rate...

.... Analytical calculations were done in different environments, for the experimental flow rates using cubic law under laminar flow for equivalent fracture aperture calculations for all experiments. Cubic law is verified with the fractured cores flow definition whereas not for homogeneous cores...

... Abstract Sand retention testing for screen selection in soft-sand completions has become an integral component to verify the screen performance. This paper describes an improved constant flow-rate test method developed for sand retention testing. The improved constant flow rate test method...

... clean-up of an open-hole deep gas well completion at production start-up. Fluid and gas flow rates, and differential pressures across the plug, were logged whenever flow was induced through the plug, to allow estimation of the relative permeability changes in the rock throughout the test sequence...

.... This geometry was placed at the bottom of a high-pressure fluid loss cell. Testing was performed at temperatures between 70°F and 180°F at constant pressure. The pressure was incrementally increased from 1,000 psi to 3,750 psi and allowed to equilibrate at each step. The flow rate was monitored through...

... could have led to reservoir mismanagement. Upstream Oil & Gas Drillstem Testing fault structure azari optimization problem pressure data Artificial Intelligence drillstem/well testing well production operation drainage area society of petroleum engineers flow rate enhance well...

... induce cap rock integrity and injection confinement issues? Would it be possible to control formation damage by controlling the injection conditions (flow rate, water salinity, etc…)? The answers provided here would give practical rules to help in adequately designing and optimizing PWRI projects...

... plugging is assessed after the completion of each test. The sanding and flow performance are shown to be a function of the aperture size, PSD, near-wellbore flow velocities, and the water cut. In low fluid flow rates, all the screen types show minimal pressure drops and perform similarly. As near-wellbore...

..., and cleanup results. drilling fluid chemistry Artificial Intelligence drilling fluid property Upstream Oil & Gas flow rate drilling fluid management & disposal completion drilling performance drilling fluid formulation reservoir section gas well gas well reservoir section fluid...

.... To describe the stochastic nature of ball sealer seating on perforations, a random number is assigned to each ball sealer, and a range is assigned to each perforation based on the ratio between flow rates through the perforations and flow rate in the wellbore. With the improved model, it can predict seating...