1-20 of 65
Keywords: producer
Close
Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Conference, September 28–October 2, 2020
Paper Number: SPE-199929-MS
... Figure 5 Simplified schematic of the PCV architecture of Producer 116P9 in Suncor/Firebag. The comparison between measured and predicted PI for Suncor/Firebag PCV trial in producer 16P9 is presented in Figure 6 . The pre-flashing PI equation is in good agreement with field data...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, March 13–14, 2018
Paper Number: SPE-189730-MS
... waterflooding injection pressure Wildmere Upstream Oil & Gas infrastructure Reservoir Management injector Efficiency producer geology porosity Injection Rate injection target evaluation Wainwright enhanced recovery constraint optimization engineer sweep efficiency...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, March 13–14, 2018
Paper Number: SPE-189758-MS
...-spot pattern configuration as shown in Figure 5b . Essentially, an additional row of producers was placed in between the regular inverted 7-spot patterns. Figure 5 (a) The Boscan field was initially developed (1947-1960) on 1000 m spacing, but subsequently (since 1960) been developed on 577m...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, March 13–14, 2018
Paper Number: SPE-189750-MS
...-horizontal producer and vertical injector-vertical producer hybrid well configuration is adopted in the type pattern simulation model. Key parameters such as perforation locations, steam quality, production-injection ratio, injection rate and SAGD transition time are optimized. It is observed that steam...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, March 13–14, 2018
Paper Number: SPE-189740-MS
... a line connecting injector and producer (Section B); the temperature variation at the mid-point compared by the CMG simulation and the analytical model (Section C), and the error between CMG simulation and analytical model at the mid-point (Section D). Heat rate at the injector and producer can...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, March 13–14, 2018
Paper Number: SPE-189723-MS
... not described here, de-watering was continued for very long durations of time but showed similar results. It should be expected that some left behind water from the de-watered zone will be produced during any recovery operation. After 500 days of de-watering, SAGD was commenced in the 2 horizontal well...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, March 13–14, 2018
Paper Number: SPE-189775-MS
... Each horizontal well pair consists of an injector about 5 m directly above and parallel to a producer, each being of identical horizontal length of about 850m. Injected steam heats the bitumen to reduce its viscosity and creates a steam chamber that grows primarily in the vertical and horizontal...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, March 13–14, 2018
Paper Number: SPE-189772-MS
... are properly accounted for, while also being immune to numerical issues like grid orientation effects that can have significant impact on results of reservoir simulation. Artificial Intelligence reservoir simulation data physics model enhanced recovery steam-assisted gravity drainage edge producer...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, February 15–16, 2017
Paper Number: SPE-184991-MS
... field development steam-assisted gravity drainage Saudi Arabia pilot mitigate key technical uncertainty Wafra Field Eocene reservoir producer SAGD steam zone development steamflood Kuwait st Eocene reservoir primary production Injection Rate carbonate reservoir validation reservoir rate...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, February 15–16, 2017
Paper Number: SPE-184967-MS
... basis, forming the gravity water-drainage assisted steam flooding technique, which has successfully solved the problem of how to produce this kind of reservoirs at their later production stage. The technique uses the combination of vertical wells plus horizontal wells. A paired horizontal wells...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, February 15–16, 2017
Paper Number: SPE-184972-MS
... learning Artificial Intelligence drawdown field trial production monitoring Upstream Oil & Gas calculation pressure drop producer steam production well pair 1 completion design FRR icd liner failure scab liner erosional velocity thermal conformance temperature profile...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, February 15–16, 2017
Paper Number: SPE-184981-MS
... technology with relevant laboratory test and field results supporting the description. thermal method bitumen Upstream Oil & Gas oil sand complex reservoir viscosity reduction Reservoir Characterization SAGD viscosity producer mud shale stringer catalyst concentration thermal...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, February 15–16, 2017
Paper Number: SPE-185005-MS
... & Gas information consideration production well flow rate pressure drop flow control device operator conformance erosion compartment enhanced recovery injector completion producer packer installation In the SAGD thermal recovery process widely used in the Athabasca oil sands...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, February 15–16, 2017
Paper Number: SPE-184990-MS
.... The development of the validated dynamic simulation model was a key success measure identified for the pilot to assist in the broader Wafra full field steamflood development decision making process. The pilot consisted of sixteen 2.5 acre inverted 5 spot patterns (16 injectors and 25 producers) with associated...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, June 7–9, 2016
Paper Number: SPE-180705-MS
... strategy steam circulation enhanced recovery circulation dilation startup producer permeability SAGD well pair pressure difference reservoir steam circulation pressure The SAGD recovery method has become a mainstream thermal production process for heavy oil/oilsands reservoirs...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, June 7–9, 2016
Paper Number: SPE-180700-MS
... operators developing oil sands located in the Grand Rapids formation or similar oil sand and heavy oil deposits. enhanced recovery steam-assisted gravity drainage thermal method steam injection SAGD western canada producer interval oil sand complex reservoir completion Production Phase well...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, June 7–9, 2016
Paper Number: SPE-180732-MS
... that a continuous steam injection with a horizontal injector placed vertically above a horizontal producer (CSI-HIHP) is a very effective method for XHO reservoirs, with high peak oil rate and significantly high recovery. This study, first of its kind for an XHO reservoir, outlines an integrated workflow...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, June 7–9, 2016
Paper Number: SPE-180734-MS
.... A complementary placement of resistances in the producer well prevents short-circuiting of steam. Pressure gradients created in the injector well are translated on to the reservoir, thus allowing for a sweep of non-condensable gasses from the steam chamber. In reservoir simulation studies, a novel convective...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, June 7–9, 2016
Paper Number: SPE-180755-MS
... between the injector and producer. A study on startup methods was conducted with the intent of optimizing temperature conformance, thermal efficiency and circulation time. The study generated several alternative startup designs, many of which employ insulated tubing strings and varied operating...
Proceedings Papers

Paper presented at the SPE Canada Heavy Oil Technical Conference, June 9–11, 2015
Paper Number: SPE-174425-MS
... production geomechanical modeling pressure gradient permeability interwell gradient average reservoir pressure gradient psia breakthrough reservoir pressure producer dilated zone nassir Alaska's North Slope Heavy Oil Sands have huge potential. There are 7 to 15 billion of barrels of oil...

Product(s) added to cart

Close Modal