1-13 of 13
Keywords: shaker
Close
Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Proceedings Papers

Paper presented at the SPE Annual Technical Conference and Exhibition, September 23–25, 2024
Paper Number: SPE-220832-MS
... management & disposal reservoir characterization mexico circulation structural geology mineral well control halite prediction shaker annular pressure drilling drilling fluids and materials fold and thrust belt geological subdiscipline case history society figure drilling challenge...
Proceedings Papers

Paper presented at the SPE Annual Technical Conference and Exhibition, September 23–25, 2024
Paper Number: SPE-220985-MS
... near the shale shaker and used to monitor and analyze returning drill cuttings while drilling 6.75-inch lateral hole sections. The varying cutting loads were measured quantitatively and qualitatively using computer vision techniques, including optical flow. The images were analyzed onsite, and data...
Proceedings Papers

Paper presented at the SPE Annual Technical Conference and Exhibition, October 3–5, 2022
Paper Number: SPE-210369-MS
... Abstract This paper discusses a field test that placed computer vision cameras on rigs' shale shakers to measure drilled cuttings and cavings. The images from the camera were processed using proprietary computer vision software and sent to the drilling team, where it was used to assess drilling...
Proceedings Papers

Paper presented at the SPE Annual Technical Conference and Exhibition, October 8–10, 2012
Paper Number: SPE-159894-MS
... Abstract Correct selection and use of solids control equipment is essential to maintain drilling fluid at its desired properties. It has also shown to be essential to avoid generation of unnecessary waste streams during drilling. Since the early 1930s shale shakers has been the dominant device...
Proceedings Papers

Paper presented at the SPE Annual Technical Conference and Exhibition, September 24–27, 2006
Paper Number: SPE-101922-MS
.... The returning sweep significantly increased re-worked fines, whereupon the shakers cleaned up. A second sweep was then pumped at 2,100 ft, a known trouble spot in the casing from the previous trips. The sweep brought a marginal increase in fines, and again the shakers cleaned up afterwards. Both sweeps were...
Proceedings Papers

Paper presented at the SPE Annual Technical Conference and Exhibition, September 26–29, 2004
Paper Number: SPE-90986-MS
... Taking a cue from the early fluids, solvency plays an important part in preventing shaker blinding and accretion. A number of fluids were screened for tar sand cleaning ability at about the temperature of circulating drilling fluid. As shown in Table 2 , one percent dispersions in water of many...
Proceedings Papers

Paper presented at the SPE Annual Technical Conference and Exhibition, October 5–8, 2003
Paper Number: SPE-84356-MS
... to build new rigs instead of modifying existing units, and the design and equipment used to enhance its performance. drilling equipment gulf natural gas operator class rig larger harsh environment rig harsh environment rig horsepower society of petroleum engineers shaker mobile offshore...
Proceedings Papers

Paper presented at the SPE Annual Technical Conference and Exhibition, September 30–October 3, 2001
Paper Number: SPE-71381-MS
... During the experiments the flow rate was slightly higher in the rotating separator than in the shale shaker. Furthermore, the drilling fluid temperature was 2.2°C higher in the rotating separator tests. Therefore, the experimental conditions were slightly more unfavourable for the rotating...
Proceedings Papers

Paper presented at the SPE Annual Technical Conference and Exhibition, October 3–6, 1999
Paper Number: SPE-56566-MS
... mud recovery technology – Centrifugal Drying – was tested as an enhancement to conventional solids control technology on four development wells in the Gulf of Mexico. Centrifugal Dryers, sometimes called rotating shakers, remove fluid from the cuttings by use of a spinning, screened basket...
Proceedings Papers

Paper presented at the SPE Annual Technical Conference and Exhibition, September 27–30, 1998
Paper Number: SPE-48944-MS
... measures in real time the total amount of cuttings flowing at the shale shakers. This data is combined with Pressure While Drilling data to further estimate hole cleaning efficiency and ECD. To overcome friction, the 9 5/8" casing of well AS-3 was run to 7720 m MD in flotation, requiring careful...
Proceedings Papers

Paper presented at the SPE Annual Technical Conference and Exhibition, October 8–11, 1989
Paper Number: SPE-19567-MS
... engineer drilled depleted sand figure shaker gulf cutter assembly mexico torque society INTRODUCTION Before discussing the techniques used in drilling the depleted sands, basic terms and definitions used throughout the paper will be reviewed. Readers already familiar with the technical...
Proceedings Papers

Paper presented at the SPE Annual Technical Conference and Exhibition, September 23–26, 1979
Paper Number: SPE-8227-MS
... shaker new computer model optimize penetration rate barite drilling fluids and materials particle-size distribution reserve pit fraction gel computer model optimize solid control Upstream Oil & Gas flow rate computer model optimize mud jetted solid control equipment mud cleaner SPE...
Proceedings Papers

Paper presented at the Fall Meeting of the Society of Petroleum Engineers of AIME, October 3–6, 1971
Paper Number: SPE-3579-MS
... a cuttings conveyor unit but so far the containers have been adapted to the rig shaker discharge with no conveyance needed. Two basic methods have been tried in an effort to clean the oil from drill cuttings. These are by heating and washing. The heating method has not been successful. Solvent washing...

Product(s) added to cart

Close Modal