1-20 of 74
Keywords: requirement
Close
Sort by
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, August 9–10, 2022
Paper Number: SPE-209930-MS
... Abstract Drill cuttings waste was recycled into new use and pilot project to utilize drill cutting waste in road and construction application were carried out. This work describes strategy and best practice to engage regulator in order to unlock regulatory requirements for the pilot on drill...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, August 9–10, 2022
Paper Number: SPE-209841-MS
... of performing this process. In situations where the design parameters and/or subsurface information change, engineers should have repeated the entire process to revise the design and/or the drilling program manually. To standardize the process, minimize repetitive tasks, and provide engineers with all required...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, August 9–10, 2022
Paper Number: SPE-209884-MS
..., channeling, cracks, cannot be ignored and requires careful evaluation. Rigorous process has been adopted in assessing the feasibility for converting existing producers into CO 2 injector. Wells disparity between the required defined basis of designs for gas producer and CO 2 injection wells governs the re...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, August 9–10, 2022
Paper Number: SPE-209852-MS
... system available typically to isolate severe losses or trouble zones while drilling. To address the major technical challenges of a large expansion ratio required to meet MSET requirement, and able to deliver potential longer MSET liner without a concern of premature expansion problem, this paper...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, August 9–10, 2022
Paper Number: SPE-209882-MS
... to ensure the AIS system is engineered and tailored to rectify the sustained annulus pressure in a less than 500-meter square deck space. production enhancement requirement well integrity completion installation and operations upstream oil & gas well intervention project management...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, August 9–10, 2022
Paper Number: SPE-209914-MS
... Abstract A new generation of Rigless ESP technology, Cable Deployed ESP (CDESP) System uses specialized cable to replace ESP, which saves rig cost and reduces production deferment tremendously. However, most CDESP in the market are applied with inverted ESP assembly, which has high requirements...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference, June 8–9, 2021
Paper Number: SPE-201014-MS
... Abstract Drilling out or working within small sizes of casing and liners requires the use of a drill string with small outside diameter tool joints to fit inside the casing/liner bore and, at the same time, a large enough connection internal diameter to pump actuating balls inside the drill...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference, June 8–9, 2021
Paper Number: SPE-201049-MS
...Aeration Energy Aerability of powder component and blend is evaluated by a powder rheometer. The regulated air within the aeration unit is administered through a diffuser to the base of the evaluated powder. Some powders require small amount of air to create a fluidized bed state, while some...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference, June 8–9, 2021
Paper Number: SPE-201085-MS
..., enabled improved decision-making for selection and LCM application requirements for subsequent jobs and development of a lost circulation strategy. The mitigation plan was put in place against losses in critical sections and depleted sand formations in Turkmenistan. It assisted in meeting the cement...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, August 27–29, 2018
Paper Number: SPE-190971-MS
... – Pre-job safety meeting , time taken to explain scope of work, safety & equipment requirements, and gain full understanding of the persons involved in that job. – Makeup WBCO BHA , time taken on the rig floor to makeup before running the WBCO assembly. – Running in Hole BHA...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, August 27–29, 2018
Paper Number: SPE-191116-MS
... (JLS-2) + 2% nano-plugging material (Nano-P) + 1.5% inhibitor (YZJ) + barite (according to drilling fluid density must be determined). Results of general performance test According to the above basic formula under room temperature conditions, according to the actual 120 °C required drilling...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, August 27–29, 2018
Paper Number: SPE-191091-MS
... international association of drilling contractors different kind platform operation reduction Well Intervention Operation Efficiency css vessel gangway subsea system Well Intervention weather conventional vessel operational time slickline unit concurrent operation requirement weather condition...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, August 27–29, 2018
Paper Number: SPE-191064-MS
... rig (TADR). The strategy is to drill all required wells on the platform, then to convert the drilling rig to completion mode and to run sand control completion. Drilling rig has large deck space, high deck load capacity and capability to accommodate 170 people, and sand control equipment can...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, August 27–29, 2018
Paper Number: SPE-191087-MS
... completion well control inflow test top kill method international association of drilling contractors Completion Installation and Operations bridge plug solid liner completion design requirement innovative solution society of petroleum engineers Upstream Oil & Gas bullnose assembly high...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, August 27–29, 2018
Paper Number: SPE-191047-MS
.... Firstly, the control requirements of the ECD profileare is satisfied, which is that the ECD<1.28g/cm 3 in the upper section and ECD>1.32g/cm 3 in the bottom of the open hole (collapse ECD=1.31g/ cm 3 , leakage ECD=1.29cm 3 ) by simulating and adjusting drilling pump flow, injected gas flow rate...
Proceedings Papers

Paper presented at the IADC/SPE Asia Pacific Drilling Technology Conference and Exhibition, August 27–29, 2018
Paper Number: SPE-191095-MS
... maximum hydrocarbon returns with low operational costs and minimum risks. The scope of this study includes consideration of well test requirement and net over gross ratio of perforation interval. Four (4) options are feasible to complete these high inclination and long departure wells: wireline tractor...

Product(s) added to cart

Close Modal