... Abstract The imagery provided as a result of the data capture via drone will be used to produce a photogrammetry model to capture the rough 3D structure of the risers. By using our solution to analyse the high-resolution imagery, we will remove subjective manual review of the data by processing...

.... Traditionally, Sea Water Intake Risers (SWIRs), which are usually made of reinforced rubber hoses, are used to supply water from water depths up to 150m to the topside, resulting in an in-take temperature of at least 15°C. Nowadays, many operators have been trying to reach colder water (5-7°C) with target SWIR...

... along with hydrocarbons. This study undertook a mechanistic, compositional modelling of a subsea gas condensate pipeline-riser system in the Norwegian sector of the North Sea. The objectives were to forecast wax and hydrate problems; estimate the operating conditions necessary for formation; predict...

... has successfully been used three (3) times and has the full confidence of BSEE and Eni. Riser Configuration with Inner Wear Liner Abstract To increase well productivity, sidetrack drilling operations can be conducted through existing production top-tensioned risers (TTRs). Since 2014, Eni...

... operations, as its previous application on deepwater wells, constructed with usage of a drilling riser, is very limited. MPD is an evolution from conventional drilling, although not every well requires the application of MPD, there are some wells that can only be completed with MPD. Conventional...

... Water depths of up to 3,650m (12,000ft). Equipped with high pressures auxiliary lines. A mining riser used in the CCZ will need to meet the following additional requirements, which will be further detailed in this paper: Abstract The world's demand for metal is rising and new...

... of optimized solutions, such as the pull-out of risers by cutting them above sea water level, inside the FPSO internal turret, which eliminated the need for diving and reduced around 50% the cost of operations, through the reduction of PLSV demand. In terms of increasing the sustainability of decommissioning...

... will be considered. sustainability turbine riser sustainable development value-applying renewable energy requirement case 1 co 2 platform offshore technology conference reduced carbon load deepwater tieback case 3 social responsibility case 2 eotec case 4 cable Introduction Using...

... and gain deeper insights into the behavior of marine risers subjected to varying environmental conditions. This intersection of offshore engineering and AI has led to the development of innovative solutions aimed at mitigating the impact of VIVs on marine risers. Abstract We developed and tested...

... As the oil and gas industry advances to fields in deeper water, new challenges arise demanding innovative solutions. The Steel Catenary Riser (SCR) is widely known as the simplest and most cost-effective solution for oil and gas offshore extraction. However, in deep water it becomes unfeasible...

..., which can also provide reference for other offshore oil fields. drilling operation offshore platform riser platform utilization illustration offshore technology conference subsea system bohai oilfield wellbore directional drilling technology offshore oil construction paper whipstock...

... The FPS is a complex coupled system. The platform is positioned via mooring lines. The risers connects the platform to the wellhead for oil and gas transportation. Under the wind, wave, and current loads, the platform drives the mooring lines and risers to move, and in turn the mooring lines...

... To enable the use of BSDL in other pre-salt fields, two main incremental developments to the BSDL design were considered necessary: Abstract Riser pull-in is a time-consuming activity. It is required to start the Floating Unit Production (FPU) and its ramp-up. In additional, conventional...

... bringing FlatFish to deepwater, in what it is believed to be a unique subsea campaign setting a number of industry firsts: autonomous deepwater inspections of flowlines, XTs, structures and risers. Such deepwater operations, carried out offshore Brazil at the beginning of 2023, have been an essential...

... response between 0.11 – 0.35 Hz. Abstract The objective of the STREAM (Steel Riser Enhanced Analytics using Measurements) Joint Industry Project (JIP) is to provide a measurement-based foundation for Steel Catenary Riser (SCR) modelling to ensure that riser response is assessed with adequate...

... The search for configurations that meet all the code criteria for the riser strength, fatigue and interference requires meticulous detailed studies and is very time-consuming task. At the same time this task has not always led to the best results because the number of variables involved is quite...

... Abstract Open water intervention riser systems (OWIRS) are used for performing intervention/workover activities on subsea wells during production or for end of life activities. The OWIRS production bore access typically consists of a main riser tubular with an annulus line tubular clamped...

... The Vortex Induced Motion (VIM) response of multi-column semi-submersible floaters may have a significant impact on the predicted fatigue life of mooring and riser systems as for example discussed in [ 4 ]. Over the last decades physical model testing using Froude-scaled floater geometries has...

... subsea production equipment vito project offshore technology conference subsea distribution hardware scr risk management installation execution model flowline subsea system contractor riser drill center development operator vito fp operation Introduction Some components...

... be reproduced when standalone models are introduced. In this study, a standalone LCO 2 carrier model and an integrated dynamic CCS model connecting the LCO 2 carrier, injection equipment, riser, pipeline, and wellbore were developed. The standalone LCO 2 carrier model predicts the behavior of a whole ship...