... dts technology upstream oil & gas production monitoring dts information frequency das fiber optic cable interface production logging production control offshore technology conference temperature gradient interrogator Introduction In recent years, the innovative approaches...

... of the new interface for rigid risers. In addition to enabling rigid lines application, TiPT will provide savings and a better operational efficiency to the Pre-salt platforms. upstream oil & gas oilfield chemistry h2s management production chemistry enhanced recovery tipt corrosion...

... bounds and identification of geotechnical risks are explained. The results show that the PME model is successful in the management of the numerous components, stakeholders, and interfaces. As a post project extension, the PME model is supplemented by an electronic equipment marking and identification...

... for the WFA project. This paper summarizes the overall design process for the WindFloat platform and mooring system that was undertaken during the project engineering phase (FEED and Detail Design), with a large focus on the description of the interface between the wind turbine manufacturer, MHI Vestas...

... naphthenate inhibition. upstream oil & gas adsorption inhibition chemistry calcium naphthenate cmp arn acid precipitate interaction non-acid chemistry enhanced recovery interfacial tension measurement mechanism aqueous phase acid ift curve interface Introduction The formation...

... strategic planning and management project management choke actuator electric valve operation subsea actuator system installation maximum sand free rate mechanical interface interface electric choke actuator electric actuator operation actuator offshore technology conference choke control unit...

... class 7 interface. The electric actuators (eActuators) provide valve operation through standard class 4 interfaces. The electric subsea control module (eSCM) is mounted on a retrievable pump module with a dedicated installation funnel. This leads to a flexible system where eSCM, actuators and jumpers...

.... It utilizes networks and cloud computers for data storage and collaboration and offers a set of Application Programming Interfaces (APIs), enabling full automation, where whole or parts of the software can be operated by other computers. The software can be accessed via any modern web browser across all kinds...

... in tension). Unlike the other functions mentioned, walking mitigation depends largely on active pressure applied by the rock and if contact at the flowline- berm interface reduces, any enhanced restraint (or ‘grip’) offered by the berm could be adversely affected. Acknowledging a tendency for flowlines...

... and a digital 3D visualization application. Its visualization module can be used in two forms: a traditional desktop interface enhanced with 3D visualizations and an immersive mode using a Virtual Reality (VR) headset. Both allow the operator to view real-time or historical data in multiple ways, perform...

... types include carbonate, sulfate and sulfide salts of divalent cations. Currently available scale dissolvers for the latter two types are often based on chelating ligand chemistry, restricted by a kinetically sluggish process of displacing the cations plus near static scale-fluid interface at the scale...

... or between pipes and equipment, the end fittings are considered, in certain applications, a critical point of the system, requiring special attention to its design in order to ensure the highest reliability and minimize its impacts on flexible pipe design. Every end fitting must, in its interface...

... the numerical simulation showed that linear surfactants may not be optimum to form type III microemulsion without the addition of a co-surfactant due to poor stability at the interface or the tendency to form type II microemulsion. Modification of their structure by elongating their tails or changing...

... wells are sourced and installed in phases. Modularization and standardization of interfaces is key for development flexibility. The challenge is to assess which pre-investments should be included and which can wait. Typically, the topside control cabinets would for a 6 cluster initial phase development...

... under proper conditions (parallel interfaces, moderate liquid attenuation), with the following characteristics: Their transit times are exact multiples of each other, and the amplitude of later multiples tend to be significantly smaller than for the first TIE. By contrast, an annulus filled...

... operated vehicle upstream oil & gas productivity tooling electrical industrial apparatus efficiency advanced remotely operated vehicle technology complexity interface inefficiency tooling interface subsea system rov operation availability offshore technology conference optimizing...

... references for qualification tests to prevent failures during deployment due to reel and skid handling, control line handling, maximum tesile strength, encapsulation slip, clamp interfaces, and connectors interfaces. Despite such efforts, there is a lack of recommended practices to prevent failures...

.... The requirements were consolidated in 8 sections: Business requirements; Reporting; Technical requirements; Security requirements; User interface; Compliance; Vendor qualifications; Administration. For each requirement, the selection desirability criteria values were set...

... a ROV class 4 torque interface for up to 2,700 Nm, while the torque required for the actuation for small-bore valves is less than a ROV class 2 torque interface (<270 Nm). This leads to an over-design as shown in Figure 2 , which is not acceptable when a machine builder needs to apply many...

... and their transitions within production and separation systems using CFD. For example, the modelling methods applicable to capture gas-liquid or liquid-liquid interface behaviour are not suitable (or practical) to also capture gas columns, liquid films or liquid entrainment phenomena, that may be important...