... miniature valve that replaces the lubricant supply function of an external lubricant pressurization system. upstream oil & gas api specification 16rcd fluid region fixture reservoir drilling fluids and materials lubricant reservoir hsl seal shaft rcd condition seal lubricant reservoir...

... & gas requirement coupler hpht fixture interface thd valve artificial intelligence subsea production equipment high pressure high temperature assembly operator completion qualification failure mode hpht subsea production tree exposure engineer OTC-30519-MS , " VXTe Deepwater...

... and qualitative analysis was performed to determine if the miscible gas mixture damaged the structure or compromised the capability of the elastomer / swellable packer to hold pressure. Two packers were swollen (separate fixtures) in diesel under conditions similar to downhole pressure and temperature. The test...

... requirement assembly fixture application test fixture hanger seal assembly casing and cementing qualification structural component configuration upstream oil & gas wellhead system completion installation and operations seal element casing design seal qualification offshore...

... polymeric seals for durations in excess of 1,000 hours. assembly upstream oil & gas bulkhead housing completion installation and operations backup ring dietle runout rotary seal fixture retainer extrusion damage test fixture drilling equipment lubricant shaft arrangement washpipe...

.... analysis methodology upstream oil & gas wellhead housing specimen assembly casing design casing and cementing application preload connector wellhead system verification analysis wellhead connector system verification analysis fixture pressure housing compression tension compression...

...) high pressure high temperature upstream oil & gas high-pressure high-temperature sensor development production logging reservoir surveillance fixture differential pressure manufacturer hpht production monitoring common-mode pressure psig sensor chip complex reservoir isolation...

... on the corrosion fatigue behavior of tensile armor wires used in flexible pipes. The scope of the research programme focused on the design of a corrosion fatigue test fixture for tensile armor wires in environments up to 15 bar CO2, and the execution of corrosion fatigue tests using different partial pressures...

... that would be used in a typical rod piston-type surface controlled subsurface safety valve. The actuator test fixture is illustrated in Fig. 3. The rod-piston actuator was taken from an existing design and incorporated into the testing fixture. Therefore, the entire test fixture had the same metallurgy...

... and pressurized internally in increments up to 2,000 psi [5]. Four sensors were rigidly mounted in an annular sleeve, 90 degrees apart and radially outward from the pipe. The face of each sensor was located approximately .015 from the exterior wall of the pipe. Figure 1 shows the pipe in the fixture...

... procedure thread compound drilling operation manufacturer composition test procedure frictional property api research project reference compound compound fixture correlation drillstring design specimen upstream oil & gas otc 7343 engagement formulation evaluation test...

... Mechanical Analysis Techniques, while the application testa were conducted using conventional size -214 O-rings in nitrogen gas test fixtures. The test results of all tests were analyzed and compared for similarities. INTRODUCTION To avoid confusion by the use of the word "rubber" for a variety of natural...

... the size of a standard ASTM Penetrometer Cup. The car size selected was A 12.5 OZ. can which is available from grocery stores containing a number of brands of Tuna Fish. The can is 4" in diameter and approximately 2 1/4" tall. baugh valve penetrometer reading standardized testing fixture...

... protector in place. The tool also retrieves and, if needed, runs the bore protector using weight set operations (no rotation). LABORATORY TESTING CASING HANGERS The test fixture used for testing the load capacity of the casing hangers is shown in Figure 6. The 18-3/4 x 13-3/8 casing hanger was placed...

... as to the feasibility of extending proven subsea wirelining technology from relatively shallow waters in the North Sea, to the deeper waters now being developed in the Gulf of Mexico. A test fixture was installed on the sea floor in approximately 1500 FSW and specific wireline manipulations were conducted to evaluate...

... and is acceptable to continue in the testing program. A test fixture such as shown in Figures 4 or 5 is acceptable for this first test. TEMPERATURE EXTREMES TESTING: After the first pressure test, the same packoff (while still installed in the testfixture) can now be subjected to gas testing attempera- ture...

... chemical environment test temperature otc 6130 modeling & simulation candidate material compression service environment american chemical society test cycle upstream oil & gas arrhenius aging technique offshore technology conference test fixture elastomer test data offshore marine...

... configuration extrusion gap seal integrity fixture reservoir surveillance production control mechanism OTe 6131 I i O-Ring S~al Failure Mechanisms by N.B. Moore; J. Hellums, and R.T.S. Chang, Cameron Offshore Engineering Copyright 1989, Offshore Technology Conference This paper was presented...

... & gas slenderness ratio fixture strength load-strain curve euler steel column test data column strength compression solid column test data test result proportional limit specimen eccentricity engineer critical stress formula ball bearing OFFSHORE TECHNOLOGY CONFERENCE 6200 North...

... pressures. All that remained was to prove the concept in the open sea. The technology was clearly applicableto underwater pipeline welding. actuator welding technique alignment fixture fixture hyperbaric welding hot tap chamber offshore pipeline evolution operation welding process...