... of mooring, water depth and environment. This status-based method uses watch areas centered around damaged static coordinates in the horizontal plane instead of the intact position. The position and heading are corrected using wind and/or hawser tension measurements. The algorithm is complemented...

... deformation stress ratio paragraph relaxation phase cable evolution offshore technology conference stress amplitude specimen copper conductor correction loading fitting Introduction In this paragraph, the analytical framework for the building of a fatigue master curve accounting for stress...

... validation process reservoir surveillance data quality calculation composition separator penalty process condition separator measurement correction redundancy validation data validation performance criteria standard condition mpfm measurement reconciled value flowrate Introduction...

... drives of the vehicle with a sufficient result. accuracy drive system directional stability cubic modification hydraulic system upstream oil & gas subsea production equipment hydraulic drive system offshore technology conference vehicle metals & mining manual correction subsea...

..., is used to calculate the logging-while-drilling (LWD) depth. However, environmental corrections must be applied to the driller’s depth resulting from the dynamic mechanical changes pipes undergo while in the borehole, with these corrections applied at the surface. These dynamic changes are due to drilling...

... loads ranging between 7% and 20% of the MBL of the tested chains. The Smith-Watson-Topper (SWT) mean stress correction model is used to transform the stress state of the tested chains into different stress states associated to different mean loads. Then regression analyses are performed and correction...

... system modeling & simulation information data assimilation mexico assimilation drifter data frontal analysis gulf correlation forecasting system correction ocean model forecast hycom altimeter data variability upstream oil & gas reservoir characterization References...

... 2MET. crest conundrum return period upstream oil & gas crest water depth correction wave period design wave crest elevation n-year wave simulation negative conundrum wave height guidance design wave approach conundrum stream function wave n-year crest loading References...

...—and correct for, as required—fluid contaminants caused by invaded mud filtrates. New measurements are combined with new algorithms to yield a harmonized contamination quantification solution that is applicable to all fluids and mud types. The quantification of drilling fluid content is at its most...

... welds and components to existing design S-N curves or developing appropriate design S-N curves from material and full-scale fatigue testing in applicable environments, and (d) developing benchmarks for analytical model validation through wellhead fatigue monitoring in real time. correction...

... high temperature operation correction fabrication sensor cell OTC-25772-MS True Downhole Measurement of Differential Pressure J.E. Hall, Letton Hall Group; N. Tiliakos, Innoveering, LLC; J. Brown, Letton Hall Group; T. Worst, Pressure-Sensor.com; R. B. Foster, University of Arkansas Copyright...

... as a practical and reliable air gap design solution for optimizing global configuration to improve deepwater floating system performance and cost effectiveness. Key words: Air Gap; Floating Structure; Model Test Correlation; Random Motion fpso offshore technology conference correction air gap system...

... floaters are considered, semisubmersibles and FPSOs. Empirical corrections are sometimes being applied in design of mooring lines, while not in general, and there is no established common industry practice on such corrections. More advanced tools and knowledge do exist in research communities, while...

... for the tow out of the graving dock and then to site. offshore technology conference paper spar tank gulfstar spar ballast skirt tank correction metocean condition configuration spar hull side keel tank kip characteristic keel tank flooding machine learning floating production system...

... not been reviewed by the Offshore Technology Conference and are subject to correction by the author(s). The material does not necessarily reflect any position of the Offshore Technology Conference, its officers, or members. Electronic reproduction, distribution, or storage of any part of this paper without...

... has been compensated during the preprocessing, however this approach has a number of limitations. It is difficult to relate the recorded seismic trace to a location in the subsurface and hence except in the case of a constant attenuation factor the amount of attenuation correction to apply...

... and the ROV pilots. The three gravity meter systems are mounted into a single deployment framewhich isolates them from shocks generated by the ROV launch and recoveryactivities. The frame is lifted by a hydraulic arm on the ROV, speciallyconstructed for these surveys. correction offshore technology...

... to be towards southerly directions. cpp site amplification storm amplification factor refraction resolution significant wave height wave energy upstream oil & gas correction variation reef seastate spectra bathymetry otc 21610 simulation australia offshore technology conference...

..., attenuation and scattering within the sediment volume, and the angular dependence of the bottom backscatter process. backscatter data impedance contrast moustier upstream oil & gas artificial intelligence otc 20866 interface application sonar contribution slope correction machine...

.... There are very significant amplitude variations that must be associated with salt induced illumination variations. These variations were not only present in the stacked amplitudes but also in the offset amplitudes. Each offset required its own correction. It was possible to significantly increase the areal...