... Abstract Subsea pipeline repair connectors have been used in the oil & gas industry for many years and are considered a valid and safe way of repairing major damages and restoring the original pipeline condition in case of an emergency repair; they can also be used for tie-ins to allow...

... Vessel - DSV and the limitations of using this vessel in adverse environmental conditions (wind, current, wave height, etc.). brazil government remotely operated vehicle offshore technology conference upstream oil & gas sub-sea system platform operation rov connector campos basin...

... thruster connector reliability netherlands government denmark government freedom auv rov sensor configuration computer sub-sea system remotely operated vehicle module pipeline subsea cable Introduction The offshore industry needs reliable remotely controlled assets to carry out...

... Abstract Deepwater pipeline repair planning and execution plays an important role to ensure the pipeline integrity during its service life. Due to the complexity of the work and capital associated, a more rigorous design and testing qualification program on the repair connector is needed...

... Abstract In Oil and Gas industry the Subsea Pipeline Repair Connectors have been developed to provide an effective sealing and installation on damaged or leaking pipelines. This paper presents a verification methodology for Subsea Pipeline Repair to confirm a product design compliance to DNV...

... different load capacities; however, no good method has been established for monitoring critical components of the clamp style connection system to matchthe computer analysis. The result is a lack of confidence for scaling the connector design up or down or extrapolating the load capacity for different...

... integrity connector the packers open hole upstream oil & gas physical contact intelligent completion upper completion wdt control line Introduction Since the initial phases of Santos basin pre-salt fields projects, Intelligent Well Completion (IWC) has been considered as one of the key...

... Abstract This paper will detail the process of developing a 36/60(72,5) kV high voltage wet mate and dry mate connector system, designed to meet the requirements of floating offshore wind turbines, and utilizing new and proven subsea technology developed to meet the requirements of critical...

... repetition or frequency-sweep rates, regardless of the tieback distance. Moreover, this topology eliminates back reflections from the multiple optical connectors above the remote circulator. The receiver arms of the DAS, DTS, and FBG interrogators only sense pure backscatter light from below the circulator...

... hydraulic and chemical lines and ends up in wet-mate connector(s) in the Umbiblical Termination Header (UTH). An Electrical Flying Lead (EFL) connects the UTH to the REDU described above. Surface components Not illustrated in the surface section in Figure 1 a power source large enough to power all...

... and lowers red zone entries beyond current mechanized handling solutions. Once set in place, surface casing strings are subjected to a higher classification of well service as structural and well loads increase in severity. To address this, a new weld-on connector qualified to connection assessment level I...

... solutions studied during HISEP™ de-risking phase to drive those high-power subsea pumps. sustainable development upstream oil & gas social responsibility connector fpso operation subsea system sustainability subsea vfd cross-section reduction complexity operator mero 3 de-risking...

... upstream subsea production system (SPS) equipment such as trees, connectors, and manifolds rated for 20-ksi or 400°F. This paper covers the project execution of production equipment for the world's first developed 20-ksi subsea field. This paper includes introduction of new technologies, digitalization...

... sub- assembly and made up in the slips. In figure 6 , the lug profiles can be seen, and this shows the three-step process that we first bring the mill over to the whipstock and slightly aligned as shown. The lugs on the connector are aligned with the junk slots in the mill. This doesn't have...

... Product requirements: Reduce cost by >20% # Reduce embodied CO 2 by >10% Reduce lead-time by 50% Reliability >99% 2 power circuits and 2 duplex ethernet channels in one connector. Full compliance with API-17F (4 th and upcoming 5 th edition). # Whole...

... casing design connector assembly fatigue performance connector specimen red zone upstream oil & gas phosphate coating rig personnel offshore technology conference anti-rotation device risk exposure badger connector iso 13679 load testing casing and cementing metal-to-metal...

.... Abstract A new method which uses elastic and elasto-plastic Finite Element analyses is developed to design a double breech-block type connector. All relevant criteria proposed by API16F are fulfilled. In addition, plastic and bearing criteria have been added to support the use of lugs for load transfer...

... and workover operations. These connections are generally made by subsea wellhead connectors and are a critical component of the subsea system due to the high level of loading that they will see throughout their operational life. As fields have continued to be discovered with increasingly high pressures...

... that includes an acoustically releasable subsea mooring connector. Evolution of Mooring Quick-Disconnect Technology Foundational Patents As stated previously, the idea of being able to disconnect a mooring line remotely has been around for a long time and the conceptualized devices range in complexity...

... drilling measurement upstream oil & gas resistance mechanical strength reliability well logging connector safety factor electrical insulation resistance log analysis drilling data acquisition strength electrical connector insulation resistance compression processing...