... of a splitter wellhead. In achieving the objective to P&A the keeper wells, an Abrasive Water Jet Cutter (AWJC) is deployed to perform an internal eccentric cut that able to penetrate five (5) cemented casing simultaneously. The cutter is paired up with Drilling Wire Saw (DWS) and Dual Drilling Machine (DDM...

... contract and the logistic vessel has to be shared with other fleets. Therefore, it is essential to develop a solid course of action to achieve the objective of utilizing HWU in GP jobs. Related to performance enhancement, some initiatives have been pursued i.e. changing the position of the barge to reduce...

.... In this case, the depth will be at 850 m. However, the main plan will always be drill through and seal off the major fault at 1230m via CWD. Continuous monitoring during execution is essential in ensuring the casing is set at desired setting depth. The primary objectives for the top section of Tall...

... temperature well cement job lbm gal sensitivity test objective spacer cement slurry dependable zonal isolation barrier vietnam slurry design hierarchy slurry Introduction Over the past decade HPHT design and execution of offshore cementing jobs in Vietnam have faced multiple challenges...

... Rate Gas Wells in the PTTEP's Block H Development in the Malaysian Deepwater region of Sabah, between 2020 and 2021. sand/solids control criteria high rate gas completion sand control presented filtercake objective gravel pack upstream oil & gas fluid loss exhibition requirement...

... Abstract The operator of field S initiated a project with a key objective to unlock and increase oil recovery while maximizing the economical oil ultimate recovery and maintaining a daily production with a ceiling unit development cost. The targeted sandstone reservoirs are shallow...

.... Several simulations were performed and they resulted in the utilization of roller boogies to minimize friction during RIH and increase the reach of coiled hose in this well. As a result, this operation achieved its main objective of displacing the completion fluid out of the well and created underbalance...

... study. The objective of the ECA is to provide defect/ crack acceptance criteria based on methodology specified by BS7910. During ECA, the respective weld sample was analyzed against pipeline operating parameters coupled with fatigue stress mainly contributed by pressure variations. Crack growth...

... to ensure cementing objectives were achieved. Project team optimized the design by using G Cement Silica blend which has been proven to eliminate fluid migration and provide good compressive strength (UCS). This has allowed additional perforation zone for the new target as CBL/VDL shown good cement bonding...

... to be too slow in adapting to changes resulting in a significant number of oil and gas projects having a high tendency of cost overruns, schedule delays and not meeting stakeholder objectives. On the other hand, the agile model employed by IT, software and technology companies offers a refreshing view...

... pressure even as more viscous formation oil enters. However, job objectives were achieved, which were formation pressure acquisition, high-quality fluid sampling, and Interval Pressure Transient Testing (IPTT) as well as Vertical Interference Testing (VIT). This paper also discusses the comparison between...

..., landing, geosteering and completion without pulling out of hole. This paper presents the results of an FMWD campaign by Repsol in Malaysia. FMWD technology was deployed in five wells with different objectives but with the common goal of enabling real-time decision making prior to the bottomhole assembly...

... of penetration improvement, which was the objective of the 8.5 inch holesection. The successful result reflects a great team effort attained by thorough planning and execution process by both drilling project team and drill bit design engineers. upstream oil & gas interaction process enhance drilling...

... intelligence air transportation aerospace & defense uas-based utm upstream oil & gas catastrophic event operation safety case new technology deliver high value result utm probe objective mitigating measure work package safety risk management inspection high value result sensor flight...

... to execution. This pilot is a single well huff and puff pilot injection is to proof the two chemicals performances concept at near wellbore area in order to meet Technology objectives and maturation. The planning covers pilot injection schemes, injection facilities, chemical preparations and pilot test’s...

... setting helped in geo-steering the well and managed to achieve directional objectives to chase the geological uncertainties. After confirming the formation dip the well was steered 6to 7ft from the bottom conductive layer with the help of distance to boundary resistivity imaging tool. Real-Time High...

... performance of some of its activities. ground transportation artificial intelligence air transportation resident uav unmanned aerial vehicle upstream oil & gas implementation vehicle poc algorithm photogrammetry drone objective construction site technipfmc aerospace & defense...

... upstream oil & gas new multi-method well placement approach society of professional well log analysts log analysis boundary tool inclination dolomite layer objective trajectory well logging symposium Bittar , M. , Hveding , F. , Clegg , N. , Johnston , J. , Solberg...

..., unmanned surface vehicle (USV) along with vessel-based "dunker" methods to upload data from each of the monitoring wells using integrated high telemetry acoustic modem technology. The main objectives of the study were to verify data could be harvested and delivered to the client using a USV along with safe...

... the objectives. All five (5) wells were successfully perforated with a total of 840 meters of perforations achieved in 40 runs, 11 of them tractor conveyed, the longest gun string was 29 meters long and the total operating time was 783 hours. The campaign was completed with and operational efficiency of 94...