... Pipeline Corrosion well integrity flowline corrosion riser corrosion resistance materials and corrosion thermally repassivation potential Subsurface Corrosion APMT corrosion rate texas 77084 FeCrAl alloy corrosion potential current density Houston storage reactor Publication...

..., the process fluids tend to be non-corrosive even in the presence of chlorides. A typical chemical process flow diagram for an organic solvent process is shown in Figure 1. In this process, the supply of olefin, as the raw material, undergoes a chemical reaction in a reactor with catalyst and becomes a new...

... Abstract Corrosion testing of austenitic stainless steel, UNS S31603 (AISI 316L), was conducted in flow-through reactors during early stages of lab setup development with the aim to obtain a superheated steam environment with H 2 S/CO 2 /HCl at 350°C and 10 bars. The test fluid; aqueous...

... of ultraviolet (UV) radiation at both sides. Test conditions Corrosion testing was conducted by immersion of carbon steel coupons in fed-batch reactors (reactors with replenishment of nutrients). Four (4) reactors were set up in this study, two biotic (in the presence of the oilfield consortium), and two abiotic...

... steel fluidized-bed reactor segment from Iowa State University s Pyrolysis Process Development Unit Facility (PPDU). This reactor segment is particularly valuable because a detailed history of operation time, temperature, and biomass feedstock was available. As previously reported for a range...

... on samples of the analyzed refinery Reactor-A. Samples were loaded in tension and subjected to impact mechanical testing to evaluate the probability of occurrence of the hydrogen-assisted cracking phenomenon. Fractography, Nondestructive testing (NDT), and scanning electron microscope (SEM) analysis carried...

... development reactor elemental map renewable energy molten chloride eutectic salt energy production backscattered electron image coupon metallic alloy corrosion behavior manuscript Houston mass loss Corrosion Behavior of Metallic Alloys in a Molten Chloride Eutectic Salt Dominic Dinh, Touba...

... the results of the testing of other samples. Subsurface Corrosion Preheater corrosion rate flowline corrosion riser corrosion reactor materials and corrosion Upstream Oil & Gas simulated high temperature geothermal environment Pipeline Corrosion well integrity chemical composition inlet...

... operation conditions in high temperature water (e.g. 288°C) and under accident conditions for reaction with super-heated steam up to 1500°C. After a loss of coolant (LOCA) accident the reactor needs to be flooded, therefore quenching the fuel rods, which would have suffered a thermal shock. It is important...

... was done in a flow through reactor for 1 and 3 week exposures. The stainless steel UNS S31254 performed well at 180°C with negligible corrosion rates both for the 1 and 3 week tests and no localized corrosion damage detected. After the testing at 350°C localized corrosion and substantial amount of NaCl...

...)3-LiOH with compositions typical of the coolant of light water power reactors have been measured for three boron compositions between 1500 ppm (by weight) and 3500 ppm and three lithium concentrations between 10 ppm (by weight) and 40 ppm over a temperature range from 30oC to 60oC using a calibrated...

... Pipeline Corrosion Production Chemistry reactor sulfide control Inhibition Sulfide nitrate effectiveness manuscript Combined Effects of Microbes and Nitrate on SRB Growth, Souring and Corrosion Bei Yin The Dow Chemical Company 400 Arcola Road Collegeville, PA 19460 United States Kenneth Wunch...

... ABSTRACT Fluoride Salt Cooled High Temperature Reactors (FHRs) are important to the world as a potential future primary electricity source, with a very high potential that the present fleet of aging Light Water Reactors (LWRs) could be replaced by FHRs. As both the fuel and coolants for FHRs...

... remediation of hydrates reactor Artificial Intelligence Production Chemistry scale inhibition polymorph calcite fouling Houston supersaturation scale deposit calcium carbonate texas 77084 permission manuscript specimen relative supersaturation deposit Mixed Calcium Carbonate and Calcium...

... Abstract Supercritical water-cooled reactor (SCWR) is an innovative Generation IV reactor and merits further research and development with the intent of being pursued for implementation in the next 30 years. The SCWR is a high temperature and high pressure water-cooled reactor in which...

..., such as dry chlorine, red fuming nitric acid and oxygen-rich environments. Any titanium fires and/or explosions occurring outside these well known conditions are considered unusual and unique. An unexpected explosion occurred in the vent line connecting at the top of a titanium reactor that was used to make...

... Abstract The supercritical water-cooled reactor (SCWR) design requires that fuel core outlet temperature will be up to 650 0 C at 25 MPa pressure to achieve optimum thermal efficiency. Selection of suitable fuel cladding materials is a critical issue for SCWR concept design. A number...

... formation. houston enhanced recovery publication division isw manuscript scenario texas 77084 biofilm reactor scenario 2 concentration permission bacteria scavenger upstream oil & gas waterflooding biocide injection batch thp treatment gu cell csa index biocidal effect Co...

... water ph wt 0 permission liquified natural gas reactor tgt absorber subsurface corrosion government work upstream oil & gas circulation water tail gas chemical reaction reaction quench water column riser corrosion absorber pipeline corrosion lng materials and corrosion tgt section...

... ABSTRACT Injection water is typically batch treated with biocides to minimize biofouling. This paper describes a study with biofilm reactors to determine the biocidal effect of TetrakisHydroxyMethylPhosphonium Sulfate ( THPS ). The results demonstrate how operators can optimize their use...