... ABSTRACT To study the spudcan punch through in a kind of multilayered clay which is composed of thick soft-thin stiff-thick soft layers, centrifuge model tests were conducted. The results indicate that there are two typical resistance profiles determined by the strength ratios of the soft...

... ABSTRACT This study aims to investigate behavior of guardrail supporting piles subjected to horizontal impact and static load using centrifuge model tests. A centrifuge testing system capable of impact and static loading was developed. A series of centrifuge model tests was carried out...

... ABSTRACT In this study, centrifuge model test, numerical simulation and hydraulic gradient test were employed to investigate the cyclic behavior of tripodpile foundation for offshore wind turbines. The short-term cyclic response of soil-pile system were investigated by centrifuge model test...

... oil & gas resistance centrifuge model test horizontal load sensor group suction anchor prototype scale load-displacement curve centrifuge test offshore technology conference soil specimen single suction anchor single anchor subsea system suction anchor triple anchor Centrifuge...

.... upstream oil & gas offshore centrifuge model test evaluation suction pile centrifuge test anchor suction anchor 2 pullout capacity vertical pullout behavior diameter pile length lee installation model suction pile vertical pullout capacity Evaluation of Vertical Pullout Behavior...

... loading capacity load cell suction pile horizontal pullout capacity pile length centrifuge model test resistance offshore Centrifugal Model Behavior of Laterally Loaded Suction Pile YouSeok Kim, TaeHoon Kim, KyoungO Kim, JongPil Lee and JinWoo Bak Daewoo Engineering & Construction Co., Ltd...

... Evaluation of the Dynamic Group-Pile Effect in Dry Sand by Centrifuge Model Tests Min-Taek Yoo, Se-Hwan Cha, Jung-In Choi, Jin-Tae Han, Myoung-Mo Kim Department of Civil & Environmental Engineering, Seoul National University, Seoul, Korea ABSTRACT It is well known that the average load for a pile...

... upstream oil & gas pullout capacity move downward suction pile offshore horizontal loading capacity model container maximum loading capacity test result model suction pile container loading capacity cho loading point centrifuge model test engineering load inclination angle...

... characteristics and high performances because of its short experience. In this research, a series of centrifuge model tests for the pile in a soil cement column horizontally loaded and the fiber model analyses of the pile were conducted to examine the effectiveness of the column wearing and the plastic response...

... results when compared with centrifuge model test performance. The deformation analysis using a non-coaxial model provides the appropriate evaluation of slope failures and more significant information for construction management of geotechnical projects in the early stage of constructions. INTRODUCTION...

... structures. A series of centrifuge model tests was performed to investigate the failure pattern of the group column type improved ground under embankment. The paper describes the collapse failure of the improved ground as well as the model test procedure. INTRODUCTION The Deep Mixing Method (DMM), a deep...

... ABSTRACT An analytical solution has been developed to estimate the vertical pullout capacity of embedded suction anchors. Validation has been made through comparisons with the centrifuge model test results. The results indicate that the vertical pullout capacity of the embedded suction anchor...

... ABSTRACT Investigation of the contaminant leakage from a post closure offshore landfill site using centrifuge model tests is presented. The leakage assessment is mainly focused toward the disturbance caused to the natural clay barrier of landfill site by construction of massive deep foundation...

... ABSTRACT A series of centrifuge model tests on embedded suction anchors have been conducted to determine the horizontal, vertical and inclined loading capacities. The centrifuge model tests include as main variables the load inclination angle and the loading point with and without flanges...

... of the input parameters in the analytical solution of mooring lines. INTRODUCTION A series of centrifuge model tests on embedded mooring lines in a sandy soil were conducted. The results were then used to calibrate the analytical solution of the mooring lines (Bang, 1996). The analytical solution models...

... ABSTRACT A series of centrifuge model tests on embedded suction anchors to determine the horizontal and inclined loading capacities have been conducted by Daewoo Institute of Construction Technology (DICT). The centrifuge model tests include as main variables the embedded depth, the direction...

... buckling). To investigate this, a series of centrifuge model tests have been conducted to investigate the uplift capacity and the loaddisplacement behaviour of pipelines buried in recently liquefied clay. Both short and long-term loadings are considered. The undrained uplift capacities were seen...

... ABSTRACT This paper describes a centrifuge model test program of suction pile installation in sand. The purpose of the centrifuge tests was to establish relationships between the applied suction pressure inside the pile and the resulting pile penetration to validate an analytical solution...

...- up spudcans near to these footprints can result in uncontrolled penetration, slewing of the rig and collision with the platform. However, there is little published information that can be used to assess the likely field behaviour. In this paper, some centrifuge model tests aimed at examining...

... that the predictions of load distribution and load impact of the sand fills dumped directly into the sea are need and to be evaluated. To predict these factors, a series of centrifuge model tests were conducted. The similarity laws between real cases and model tests as well as the accuracy of prediction were verified...