... wells, with monitoring sections at varying distances to the monitored well, can be used to delineate both wetted and conductive hydraulic fracture dimensions. Similar to a vertical monitor well, instrumentation for a slant monitor well may also consist of fiber optics and pressure/temperature gauge...

... annual technical conference gauge proppant united states government sand control completion exhibition presented well international petroleum technology conference openhole gravel packing execution friction Introduction The wells discussed in this paper were completed in the PTTEP's...

... tubing hanger retrievable bridge plug iptc-22891-ea international petroleum technology conference co well intervention efficiency well intervention downhole intervention production monitoring bridge plug gauge personnel Introduction An LNG plant in Australia was designed to maximize...

... Upstream Oil & Gas pressure data input parameter gauge drillstem/well testing wellbore storage effect boundary storage effect Qa Qc Drillstem Testing PTA Interpretation pressure transient analysis rate data pressure rate data typical example gauge data international petroleum...

... a workover operation. Therefore, it is important to capitalize on all opportunities to retrieve and analyze defective downhole equipment to minimize future malfunction, increase the life expectancy, reduce operational cost, and enhance efficiency. This paper studies several downhole gauge challenges...

... immobile mass short string gravity feed drilling fluids and materials long string fluid level application gauge hesitation squeeze IPTC-17850-MS Fracture Closure Stress Treatment in Low Fracture Pressure Reservoir Y. Lai, and B. Woodward, ExxonMobil Exploration and Production Malaysia Inc...

... transmission system gauge Completion Monitoring Systems/Intelligent Wells platform hardware Upstream Oil & Gas landing server downhole sensor Offshore Platform software international petroleum technology conference wellsite connector Reservoir Engineer interface Malaysia...

...IPTC-18144-MS Permanent Downhole Gauges Selection for HPHT and Fractured Basement Reservoirs, Vietnam H. V. Pham, CuuLong Joint Operating Company; C. A. Green, G Frac; C. Yapp, Weatherford; T.M. Le and A. Butt, CuuLong Joint Operating Company Copyright 2014, International Petroleum Technology...

... production control production logging application North Kuwait Completion Monitoring Systems/Intelligent Wells optical fiber real time system deep ht-hp well production monitoring Reservoir Surveillance data Acquisition unit installation gauge cable Bragg fiber fiber optic cable...

... innovative downhole sand control solution condensate reservoir Upstream Oil & Gas profile 2 iptc 17477 ceramic screen gauge screen Well Condition erosion gauge ceramic screen gravel ceramic ring gauge sand rate IPTC 17477 Ceramic Screens - An Innovative Downhole Sand Control Solution...

... ½ in. OD. Therefore, the use of capillary tubing for cementing operations has not been considered until recently. This paper will feature a project in Australia where a capillary unit was employed to abandon a well with cement, while concurrently installing downhole pressure gauges to comply with local...

... Abstract Permanent Downhole Gauge (DHG) technology has been widely used in deep water reservoir development in the last decade and is playing an increasingly significant role in real time reservoir/well surveillance and reservoir management. Tidal signal extracted from the highly accurate...

... production logging hydrate production research well program gauge DTS temperature dts system fraction international petroleum technology conference void fraction fluid level Phoenix gauge hydrate production test mKB dts temperature transient fluid-level monitoring Abstract Temperature...

... in the data acquisition program. The main challenge in this high temperature environment for formation testing acquisition is that pressure gauges need to be stabilized to eliminate a transient effect due to high temperature, in order to obtain an accurate pressure measurement. This can lead to longer logging...

... this will be outlined. Optimum production depends on the availability of downhole data. Presently these wells are completed with a permanent gauge located below the packer which provides an effective measure of down hole flowing pressure. However, to date no ESP gauge, as is routinely installed in conventional ESP...

..." OD, 1- 1/8" ID Schlumberger DST tools designed for slimhole 5", 4-1/2" liners or casings) and HP-HT gauges for the BHP & BHT measurements. Perforation was planned to be done with SLB WL with overbalance. As the expected BHP was 13,000 psi, BHT = 380°, and WHP was expected to be 12,000 + psi, dry...

... Abstract The principal considerations in designing a permanent gauge system are the accuracy, resolution and stability of the acquired data (pressure, temperature, flow) and the reliability with which this data can be transmitted to the end user. Cable to Surface gauges combined with the ISU...

.... To achieve this, the downhole test set up comprised of a series of stacked retrievable packers with tail pipes separating successive test intervals. The tailpipe of each packer was equipped with wireline nipple profiles and an external gauge carrier with multiple gauges featuring acoustic telemetry...

... tester pressure test sand face pressure reservoir pressure pressure measurement pressure data gauge Copyright 2007, International Petroleum Technology Conference This paper was prepared for presentation at the International Petroleum Technology Conference held in Dubai, U.A.E., 4 6 December 2007...

... Abstract Both conventional and non-conventional well testing and sampling operations require some form of design a priori. Due to the uncertainties in input parameters during the test design stage, test sequence and duration are mostly adhered to especially when memory gauges are being used...