... orientations of 30°, 60°, and 90° with respect to the horizontal. Results indicated different peak strengths at failure with highest and lowest values for the 90° and 30°-specimens, respectively. Failure occurred at different mean effective stresses with different magnitudes of pore water pressure built up...

... ABSTRACT: The magnitude and orientation of the in-situ stresses are greatly impacted in areas where the ground elevation changes dramatically within the field boundaries. The stress model for XGS field, located in onshore China, is constrained using a comprehensive workflow starting from...

... orientation, that reflects the uncertainties in all the observations or indicators used to constrain the stress state. This method is demonstrated using the characterization data for the EGS Collab Experiment 2 site. The output of the analysis is used to guide the design of the planned stimulations...

...; Zhuang et al., 2020). injection cyclic injection rock mech fracture propagation upstream oil & gas fracture specimen experiment zimmermann experiment zhuang hydraulic fracturing hydraulic fracture granite zhuang gonghe granite aperture pocheon granite propagation orientation...

... the in-situ stress, which agrees well with the results calculated by using Mogi-Coulomb criterion. 1. INTRODUCTION In-situ stress is very important for oil and gas drilling and hydraulic fracturing stimulation operations. Accurate knowledge of stress magnitude and orientation can help us to design...

... that homogeneity of discontinuity orientations are preserved, which may or may not be defined by geological boundaries such as faults, river tributaries, lithology etc. The proposed model accounts for the deviation of strikes along slopes, the dip amount in a particular section which varies from bottom to top...

.... Regional stress orientation suggests that fault system 1 has higher shear to normal stress ratio, which might be the main reason why those faults are capable of hosting large events without much drive from fluid injection. Geomechanical modeling was performed combining hydraulic fracture modeling with dual...

... precipitation orientation particle ARMA 22 0763 Fluid Induced Elemental and Mineralogy Alterations of Caney Shale Awejori, G., Xiong, F., Katende, A., Radonjic, M.* Hydraulic Barrier Materials and Geomimicry Laboratory, School of Chemical Engineering, 420 Engineering North, Oklahoma State University...

... toughness detournay pre-existing discontinuity lecampion orientation bunger dimensionless toughness propagation regime slat101 hydraulic fracture criterion hf propagation ARMA 22-239 Experimental investigation of hydraulic fracture growth in an anisotropic rock with pre-existing...

... variability artificial intelligence probe stereographic projection table reservoir geomechanics magnitude estimation borehole plane perpendicular table 1 procedure journal geometry rock mechanic orientation mining science ARMA 22-286 Transient inverse analyses of overcoring data...

... exchanges. For the second experimental testbed, the EGS Collab team visually mapped the distribution, orientation, and nature of open and healed fractures exposed along the drift wall in the Sanford Underground Research Facility 4100 feet below ground surface, and within the eleven boreholes drilled...

... characterization orientation upstream oil & gas hydraulic fracturing saudi aramco deformation rotation conjugate shear fracture paradox basin configuration doelling fracture characterization reservoir geomechanics shear fracture perturbation magnitude laramide moab tongue public...

... Volume as a composite made of a homogeneous matrix that contains ellipsoidal cracks of various orientations and ellipsoidal mineral inclusions that represent biotites. The mechanical properties of the bulk rock are obtained by two-step Mori-Tanaka homogenization. This model captures the propagation...

... known that these features act as weakness planes in the rock matrix and thus studying the mechanical behavior of shale should incorporate the influence of bedding planes. Numerous investigations have been conducted so far to understand the influence of bedding plane orientation on the deformation...

... distribution of fractures across the field or reservoir. The geoscientists seek to intersect areas with a high density of fractures and good connectivity, where the drainage of the matrix is more effective. The orientation of the wells should be in accord with the geometrical and geomechanical parameters...

... algorithm orientation boualam fractal dimension dm correlation coefficient algeria ARMA 22 311 FRACTAL ANALYSIS APPLIED TO NATURALLY FRACTURED RESERVOIRS ANALOG Sofiane Djezzar, Aldjia Boualam, Abderraouf Chemmakh, Aimen Laalam, Habib Ouadi, Ahmed Merzoug, University of North Dakota, Grand Forks...

... structural grain. Monitoring included electrical resistivity tomography (ERT) that shows the presence of a well-defined electrical conductivity high that defines a fold structure occupying much of the test bed with an orientation similar to the local structure. The nature of this folded conductive unit...

... integrating the density logs for the vertically- oriented core plugs. The horizontal minimum stress inferred from horizontal core plugs matches well with bounds obtained by hydraulic fracture stress testing and corresponding to an average minimum tectonic strain of 170 microstrain. The maximum stress is found...

.... The first field, situated in the Eastern region, denotes smaller fractures with three different orientations. In comparison, the second field, located in Western domain, is dominated by long faults, oriented N-S. However, the most predominant direction is NW-SE. In the first part, the connectivity...

... ABSTRACT: Rotary steering drilling tool with the push-the-bit function can control directional drilling orientations with biasing unit pushing against the well wall. In this paper, taking the biasing mechanism as the research object, based on the mechanical model of the steering drilling tool...